Determine the maximum actual bending stress in the following beam. Assume normal temperatures, bending about the strong axis, and no incising. Ignore the weight of the beam.Load:wD = 100 lb/ftwLr = 240 lb/ftLoad combination:D + LrSpan:L = 7 ftMember size:4 x 10Stress grade and species:No. 1 Douglas Fir-LarchUnbraced length:lu = 0Moisture content:MC < 19 percentLive load deflection limit:Allow. Δ ≤ L/360

Determine the maximum actual shear stress in the following beam. Do not reduce the shear based on NDS Section 3.4.3. Assume normal temperatures, bending about the strong axis, and no incising. Ignore the weight of the beam.Load:wD = 140 lb/ftwLr = 240 lb/ftLoad combination:D + LrSpan:L = 14 ftMember size:4 x 8Stress grade and species:Select Structural Douglas Fir-LarchUnbraced length:lu = 0Moisture content:MC > 19 percentLive load deflection limit:Allow. Δ ≤ L/360

Determine the ASD adjusted design compression strength perpendicular to grain, Fc⊥’, for the following beam. Assume normal temperatures, bending about the strong axis, and no incising. Ignore the weight of the beam.Load:wD = 200 lb/ftwLr = 450 lb/ftLoad combination:D + LrSpan:L = 7 ftMember size:4 x 8Stress grade and species:No. 1 Douglas Fir-LarchUnbraced length:lu = 0Moisture content:MC > 19 percentLive load deflection limit:Allow. Δ ≤ L/360

Use APA Technical Note Q225 entitled Load-Span Tables for APA Structural-Use Panels and ASD procedures to answer the following question.The spacing of joists in a flat roof is 19.2-in. o.c. Roof dead load = 9 psf. Snow load = 59 psf. Roof sheathing is to be an APA rated plywood sheathing, and panels are to be oriented in the strong direction. The load is governed by deflection limits of L/240 for snow load and L/180 for total load. Only consider these limits. Assume multi-span, normal duration of load, dry conditions, and panels 24 inches or wider. Would a panel with a span rating of 32/16 be adequate?

Determine the ASD adjusted design compression strength perpendicular to grain, Fc⊥’, for the following beam. Assume normal temperatures, bending about the strong axis, and no incising. Ignore the weight of the beam.Load:wD = 260 lb/ftwLr = 180 lb/ftLoad combination:D + LrSpan:L = 14 ftMember size:4 x 14Stress grade and species:No. 1 & Better Douglas Fir-LarchUnbraced length:lu = 0Moisture content:MC < 19 percentLive load deflection limit:Allow. Δ ≤ L/360

Determine the maximum actual bending stress in the following beam. Assume normal temperatures, bending about the strong axis, and no incising. Ignore the weight of the beam.Load:PD = 440 lbPLr = 1,920 lbLoad combination:D + LrSpan:L = 11 ftMember size:4 x 12Stress grade and species:No. 1 & Better Douglas Fir-LarchUnbraced length:lu = 0Moisture content:MC < 19 percentLive load deflection limit:Allow. Δ ≤ L/360

A pin-connected wood truss is loaded and supported as shown. Determine the axial force produced in member GH if PB = 700 lb, PC = 1,900 lb, PD = 2,900 lb, L = 6 ft, and h = 8 ft. Positive choices indicate tension. Negative choices indicate compression.

Determine the ASD adjusted design bending strength, Fb’, for the following beam. Assume normal temperatures, bending about the strong axis, and no incising. Ignore the weight of the beam.Load:PD = 440 lbPLr = 1,280 lbLoad combination:D + LrSpan:L = 7 ftMember size:4 x 6Stress grade and species:No. 1 Douglas Fir-LarchUnbraced length:lu = 0Moisture content:MC > 19 percentLive load deflection limit:Allow. Δ ≤ L/360

Determine the maximum actual shear stress in the following beam. Do not reduce the shear based on NDS Section 3.4.3. Assume normal temperatures, bending about the strong axis, and no incising. Ignore the weight of the beam.Load:wD = 140 lb/ftwLr = 240 lb/ftLoad combination:D + LrSpan:L = 7 ftMember size:4 x 6Stress grade and species:No. 1 Douglas Fir-LarchUnbraced length:lu = 0Moisture content:MC > 19 percentLive load deflection limit:Allow. Δ ≤ L/360

Use APA Technical Note Q225 entitled Load-Span Tables for APA Structural-Use Panels and ASD procedures to answer the following question.The spacing of joists in a flat roof is 24-in. o.c. Roof dead load = 15 psf. Snow load = 55 psf. Roof sheathing is to be an APA rated plywood STRUCTURAL I sheathing, and panels are to be oriented in the weak direction. The load is governed by deflection limits of L/360 for snow load and L/240 for total load. Only consider these limits. Assume multi-span, normal duration of load, dry conditions, and panels 24 inches or wider. Would a panel with a span rating of 32/16 be adequate?